Optical system

Light source: osram 550w bulbRated life: 5,000 hoursColor Temperature: 9600KAdjustable Focus: With a high precision glass lens, electronically linear highdefinition focusAngle Degree: 1.2° Electrical parametersInput voltage: AC 100V-240V 50/60HzTotal power: 980WSignal interface: 3-core XLR waterproof signal socket input/outputPowerinterface: Waterproof power socketOptical outlet diameter: 300mm "World firs"

Effect

Range:8kmhorizontal scanning Angle 540°, vertical scanning Angle 270’,automatic returncorrection and 16Bit precision fine-tuning functionFlash: 1-20Hz per second fast stroboscopic, with pulse stroboscopic, synchronous asynchronous stroboscopic effectadjustable Light: The dimming is smooth and flicker-freeleng Mirror 1:1 octa prism, can be independently bidirectional rotation andsuperposition to create a richer beam effectcolor Disk: color sheet disk 13+1 color temperature sheet available at2500k/3200kFixed pattern plate: 14+1 can be two-way dithering, two-way water effectadjustable Focus: 0-100% linear electric focus

Physical/mounting characteristics net

Amount:52kgProtection level: IP65Dimensions:524*365*867mmthe lamp adopts high-strength die-cast aluminum shell, anti-UV treatment, high temperature resistance, anti-aging; Copper tube fin type heat dissipation

Software and Control

Control channels: Standard 16 channelsTransmission protocol: DMX512Horizontal and vertical using non-touch magnetic encoder positioning systemMenu display: LCD display, Chinese and English language can be switched atwill, font can be reversed 180. Display

2sets of can,USB,32-Bit 8051,STC32G 12K128, high precision 12-bitADC,DMA support(TFT color screen,ADC,4sets of serialport,SPI,12CDMA)

Storage buffer up to 64K BYTES. Support ADCtoRAM,SPI<=>RAM,12C<=>RAM,serial<=>RAM,RAM<=>color screen andRAM<=>RAM automatic data transferI/O port: All I/Os can support interrupt and power-saving/power-off mode wake-up, and each I/O can be configured into 4 interrupt modes: high interrupt, lowinterrupt, rising edge interrupt and falling edge interrupt. Each group of I/Oports has its own independent interrupt vector entry address, which supports 4interrupt priorities. 16-bit advanced PWM timer: Group A can be configured into 4 pairs ofcomplementary/symmetric/dead zone control PWM or capture external signals, group B can be configured into 4 PWM output or capture external signals, group A and group B can be different periods, respectively set separately, supportorthogonal encoder function.The clock source of the two groups of advancedPWM timers can reach up to 72MHz, which can work at different frequencieswith the CPU. Comparator: The positive input is P3.7/CMP+ by default, and can also be setto P5.0, P5.1 or the ADC input: ADCO/ADC1/ ADC.2.,ADC14;The negativeinput side of the comparator defaults to P3.6/CMP., which can be set tointernal 1.19v output lnto the

Choose STC3zG1ZK128-LQrr64/LQrr48/LQrr32 series microcontrollerReasons:

Do not need external crystal oscillator/do not need external reset of the MCU, can also output clock and low level reset signal to the peripheralFPGA/DSP/GPU/CPU/MCU use, on the chip EEPROM function can bedirectly simulated, itself is an emulator, no need Special emulator, programmable in the system, no need for a special programmer, can bedeveloped from the remote upgrade functionAbout 70 times faster than the traditional 8051 (at the same clockfrequency),most of the instructions are completed by 1 clock, high-speedkernel, Multilevel pipelineHigh-speed 12-bit ADC, more than 800,000 times/SEC, external 15channel,internal 16 channel ADC 15 used to measure the internal referencevoltage,can be reversed working voltage such as battery voltage, supportexternal reference source ultra-low power consumption: 1, power downmode,Typical power consumption:0.4HA;2, idle mode, typical <1mA; 3, normal work, typical <2mA;4, electricity/power saving mode can be UART/SPII2C/NTO // all 10 interrupt NT1/INT2/INT3 //INT4 external interruptComparator/low voltage interrupt or internal power off wake-up timer wakeup32 bit widthThe registers used by the kernel for arithmetic logic operations and datamovement are 32 bits wide. Through 32 bit registers,The internal EDATA areacan be directly single clock 32-bit data width read and write operations ★32- bit addition and subtraction instruction: branch Hold 32-bit addition andsubtraction instructions that can be completed by a single clockHardware 32-bit multiplication and division arithmetic units: All single-chipcomputers in theSTC32G series extend signed and unsigned 32-bitmultiplication and division arithmetic units. High system efficiency.the instruction efficiency of STc32G series running at30MHzoperatingfrequency is equivalent to about 60MHz ZMO for frequencymemory read and write faster: based on the reason of the instruction system, some popular 32-bit machines can not directly read and write to the memory, must write the target address of the memory to the register, and then indirectaccess.STc32Gseries for direct read and write to memory with 8 - and 16-bitaddress widths. The external port supports Bit operation, and the operation is more flexible:some popular32-bit machines do not have bit-band function, externalPartial ports can only be read and written to the whole group.If you want tomodify some ports in the whole group, you must add themAdditional bits and sum bits or operations. The STC32G series supports bitoperation instructions for more flexible operation.